Zoning decides what you can build before design starts. In Seattle, a lot’s zone sets how many homes can go on it, how tall they can be, and how much of the lot they can cover — and the rules changed fundamentally in 2025 and 2026. If you own a lot or are looking at one, the zone is the first thing to read, and the second thing to verify, because the code is mid-transition and the only authoritative answer for a specific parcel comes from the city’s own map.

How to read a zone label

A Seattle zone label packs three pieces of information into a short code. The letters name the zone family: NR is Neighborhood Residential, LR is Lowrise multifamily, MR is Midrise, HR is Highrise, NC is Neighborhood Commercial, and the rest are Commercial, Seattle Mixed, industrial, and Downtown families. A number right after the letters is the intensity tier — LR1 is gentler than LR3. A number after a dash is usually the height limit in feet, so NC3-65 is a Neighborhood Commercial 3 zone with a 65-foot height limit. A suffix in parentheses — (M), (M1), or (M2) — marks a Mandatory Housing Affordability tier, meaning the parcel received extra development capacity in exchange for affordable housing. Learn to read the label and you can size up a lot in seconds.

Neighborhood Residential (NR): the big change

NR is where most Seattle houses sit — the former single-family zones, renamed in 2022 and then rewritten by the Phase One middle-housing code that took effect January 21, 2026, implementing Washington’s HB 1110. The old NR1, NR2, and NR3 lot-size categories are gone, consolidated into a single NR zone. As the code stands in 2026, a residential lot in NR allows at least four dwelling units — six within a quarter mile of a major transit stop, or when affordable units are included. The base height limit is 32 feet, up to 42 feet for developments of three or more units that meet setback and form conditions. Lot coverage runs up to 50 percent of the lot, and up to two ADUs are allowed per lot. That is a different city than the one-unit-per-lot rule that governed these streets for decades, and it is why so many ordinary Seattle lots are now infill opportunities.

Lowrise (LR1, LR2, LR3): townhouses and small apartments

The Lowrise zones are the transition layer between detached-house streets and busier corridors, and they carry the bulk of Seattle’s townhouse and small-multifamily construction. LR1 is the gentlest — rowhouses, townhouses, cottage clusters, and small apartment buildings, generally three stories, with a 32-foot height limit and a floor area ratio around 1.0, rising to 1.3 with MHA. LR2 allows more height and density and is the workhorse zone for modern townhouse rows, with height around 40 to 42 feet under recent updates. LR3 is the most permissive Lowrise zone, for small apartment buildings and stacked-flat configurations, at 40 feet base height and up to 50 feet with MHA, with floor area ratios up to about 2.0 to 2.2. The higher the number, the more building the lot supports — and the more the numbers matter to what the finished project is worth.

MHA: the affordability trade

Mandatory Housing Affordability has applied citywide since 2019. The deal is simple: the city grants additional height and floor area, and in exchange the project provides affordable homes — typically 5 to 11 percent of the units — or pays into the city’s affordable housing fund. That is what the (M) suffix on a zone means, and it is why two lots with the same base zone can allow different amounts of building. MHA is a cost on every project it touches, and it is also the reason the extra capacity exists at all. Budget for it early; it is not a line item you discover at permit.

What zoning doesn’t tell you

Zoning is the starting point, not the whole answer. It doesn’t tell you about environmentally critical areas on the lot, design review, SEPA, utilities, access, or the overlays that apply to specific streets. And right now it doesn’t tell you the final answer at all: Phase Two updates are still moving through the City Council, and the Centers and Corridors legislation — new rezones and MHA on rezoned properties — was transmitted in January 2026 but is held up by a SEPA appeal, with Council consideration expected in early 2027. Treat every figure in this guide as orientation as of 2026. For any specific parcel, confirm the zone and the current rules on the SDCI Property Information Map before you rely on them — and if the lot matters, get a feasibility read from someone who builds in the zone.

Frequently asked questions

How do I find out what zone my lot is in?

Use the SDCI Property Information Map on the City of Seattle website — search the address and it shows the zone, lot size, and overlays. That map is the authoritative source for a specific parcel. Anything else, including this guide, is orientation.

How many units can I build on a Seattle residential lot?

In a Neighborhood Residential (NR) zone, at least four dwelling units as the code stands in 2026 — six within a quarter mile of a major transit stop or when affordable units are included. Lowrise zones allow more, depending on the tier. The exact number for your lot depends on the zone, the lot, and the rules in effect when you apply.

What is MHA?

Mandatory Housing Affordability, in effect citywide since 2019. The city grants additional height and floor area, and the project provides affordable homes — typically 5 to 11 percent of units — or pays into the city’s affordable housing fund. The (M) suffix on a zone marks the MHA tier.

Can zoning change after I buy a lot?

Yes. Seattle is rezoning in stages — the Phase One middle-housing code took effect in January 2026, Phase Two updates are still moving, and Centers and Corridors rezones are pending. A lot’s zone today is not a guarantee of its zone in two years, which is one more reason to verify the current map and the pending legislation before you buy.